现代制造工程 ›› 2026, Vol. 552 ›› Issue (9): 84-91.doi: 10.16731/j.cnki.1671-3133.2026.09.010

• CAD/CAE/CAPP/CAM • 上一篇    下一篇

面向轻量化的连杆组强度分析与焊接仿真协同优化设计

周志红, 朱奇   

  1. 湖南工业职业技术学院机械工程学院,长沙 410208
  • 收稿日期:2025-11-26 出版日期:2026-09-18 发布日期:2026-10-22
  • 通讯作者: 朱奇,硕士,教授,主要研究方向为工程机械结构优化、液压传动设计。E-mail:632430930@qq.com
  • 作者简介:周志红,硕士,副教授,主要研究方向为工程机械结构设计、液压传动控制。
  • 基金资助:
    长沙市自然科学基金项目(Kq2402106);湖南省教育厅科学研究项目(23C0587)

Collaborative optimization design of strength analysis and welding simulation for lightweight rod group

ZHOU Zhihong, ZHU Qi   

  1. School of Mechanical Engineering,Hunan Industry Polytechnic,Changsha 410208,China
  • Received:2025-11-26 Online:2026-09-18 Published:2026-10-22

摘要: 针对混凝土泵车臂架系统连杆组在轻量化设计中因忽略焊接工艺影响而出现的质量问题,提出了一种强度分析与焊接仿真协同优化设计方法,该方法通过构建设计与制造一体化的闭环解决方案,可以有效平衡大型焊接构件的结构强度与焊接工艺性。基于HyperMesh软件、Simufact Welding软件与ANSYS软件构建联合仿真平台,对连杆组不同焊接顺序的焊接过程进行模拟,通过对比分析等效应力与总变形量,确定最优焊接顺序;进一步提出结构优化方案,调整焊缝参数,并进行多工况强度校核与焊接仿真验证。优化对比结果表明,连杆组优化后,三角连杆与直连杆的最大等效应力分别降至469.02 MPa和267.31 MPa,降幅达12.5 %和16.8 %;焊接最大总变形量分别降至4.57 mm和3.13 mm,降幅分别为12.6 %和11.8 %;连杆组的总质量减少了3.2 %,设计方法较好地提升了大型焊接构件结构强度与焊接工艺性之间的平衡性。该技术已在泵车的臂架、转台等核心部件开发中推广,取得了较好的应用效果。研究成果为大型焊接构件的精细化设计与制造提供了有效的工程范例。

关键词: 轻量化, 连杆组, 强度分析, 焊接仿真, 协同优化

Abstract: To address quality issues arising from neglecting welding process impacts during lightweight design of concrete pump truck boom rod group,a collaborative optimization method integrating strength analysis and welding simulation was proposed. This approach established a closed-loop solution integrating design and manufacturing,effectively balancing structural strength with weld ability for large welded components. A joint simulation platform utilizing HyperMesh,Simufact Welding,and ANSYS was established to simulate welding processes with varying sequences for the rod group. By comparing equivalent stresses and total deformation,the optimal welding sequence was determined. A structural optimization scheme was further proposed,adjusting weld parameters,followed by multi-condition strength verification and welding simulation validation. Optimization comparisons revealed that post-optimization,the maximum equivalent stress in the triangular and straight connecting rods decreased to 469.02 MPa and 267.31 MPa respectively,representing reductions of 12.5 % and 16.8 %. The maximum total welding deformation decreased to 4.57 mm and 3.13 mm respectively,representing reductions of 12.6 % and 11.8 %. The total mass of the rod group decreased by 3.2 %,demonstrating that the design methodology effectively enhances the balance between component strength and weld ability for large welded components. This technology has been successfully applied in the development of core components such as the boom and turret of concrete pump trucks,yielding favourable results. The research findings provide engineering examples for the refined design and manufacturing of large-scale welded structures.

Key words: lightweight, the rod group, strength analysis, welding simulation, collaborative optimization

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn