现代制造工程 ›› 2026, Vol. 553 ›› Issue (10): 109-115.doi: 10.16731/j.cnki.1671-3133.2026.10.013

• 制造技术/工艺装备 • 上一篇    下一篇

0Cr17Ni4Cu4Nb精密轴类件环形槽车削表面质量仿真与试验分析

易震海1, 廖翔1, 商怡1, 张佳伟1, 刘泽2, 庄鑫2   

  1. 1 中国航发贵州红林航空动力控制科技有限公司,贵阳 550000;
    2 沈阳航空航天大学,沈阳 110121
  • 收稿日期:2026-01-23 出版日期:2026-10-18 发布日期:2026-11-05
  • 通讯作者: 廖翔,硕士,高级工程师,主要研究方向为精密加工工艺。E-mail:517900901@qq.com
  • 作者简介:易震海,硕士,高级工程师,主要研究方向为精密加工工艺。E-mail:zhenhaiy-honglin@163.com

Analysis and research on surface quality of ring groove turning of 0Cr17Ni4Cu4Nb precision shaft parts

Yi Zhenhai1, Liao Xiang1, Shang Yi1, Zhang Jiawei1, Liu Ze2, Zhuang Xin2   

  1. 1 AECC Guizhou Honglin Aero Engine Control Technology Co., Ltd., Guiyang 550000,China;
    2 Shenyang Aerospace University,Shenyang 110121,China
  • Received:2026-01-23 Online:2026-10-18 Published:2026-11-05

摘要: 0Cr17Ni4Cu4Nb精密轴类件被广泛地运用于航空发动机。由于其自身的难加工性,导致该零件在精密车削切槽过程中易出现表面质量难以控制的问题。使用有限元模拟与试验验证相结合的方法,系统研究了0Cr17Ni4Cu4Nb精密轴类零件环形槽车削过程中工艺参数对槽表面质量的影响,重点分析了主轴转速和进给量对表面粗糙度、硬度、微观形貌及残余应力的作用机制。研究结果表明,当主轴转速为600 r/min、进给量为0.02 mm/r时,可获得最低表面粗糙度值(Ra=0.18 μm);提高主轴转速至800 r/min时,表面硬度显著提高,达到36.83HRC,同时仍保持Ra<0.25 μm。通过增大进给量可有效调控残余应力分布。在实际加工中,为兼顾生产效率与表面质量,建议采用较低的主轴转速和进给量以获得优质表面;若需提升表面硬度,可适当提高主轴转速。

关键词: 0Cr17Ni4Cu4Nb, 轴类零件, 车削, 表面质量

Abstract: Precision shaft components made of 0Cr17Ni4Cu4Nb are widely applied in aero-engines. Owing to its inherent poor machinability,the surface quality is difficult to control during precision turning and grooving operations. Combining finite element simulation with experimental verification, the influences of process parameters on the groove surface quality of 0Cr17Ni4Cu4Nb precision shafts in circumferential groove turning are systematically investigated. Special emphasis is placed on analyzing the action mechanisms of spindle speed and feed rate on surface roughness,hardness,micro-morphology and residual stress.The research results show that the minimum surface roughness value (Ra=0.18 μm) can be obtained at a spindle speed of 600 r/min and a feed rate of 0.02 mm/r. When the spindle speed is increases to 800 r/min,the surface hardness rises significantly to 36.83HRC,while Ra remains below 0.25 μm. Increasing the feed rate enables effective regulation of residual stress distribution. For practical machining,low spindle speeds and feed rates are recommended to achieve superior surface quality while balancing production efficiency. If higher surface hardness is required,the spindle speed can be moderately elevated.

Key words: 0Cr17Ni4Cu4Nb, shaft parts, cutting, surface quality

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn