现代制造工程 ›› 2026, Vol. 552 ›› Issue (9): 1-9.doi: 10.16731/j.cnki.1671-3133.2026.09.001

• 试验研究 •    下一篇

转速比对圆柱滚子离心干式超精滚抛效果的影响

梁建新1, 翟勋政2, 娄堂云1, 王兴富3,4, 王嘉明3,4, 李秀红3,4   

  1. 1 经纬智能纺织机械有限公司,晋中 030600;
    2 中国航发动力股份有限公司,西安 710000;
    3 太原理工大学机械工程学院,太原 030024;
    4 成性制造技术山西省国防先进技术创新中心,太原 030024
  • 收稿日期:2025-11-25 出版日期:2026-09-18 发布日期:2026-10-22
  • 通讯作者: 李秀红,教授,主要研究方向为精密零件表面光整加工。E-mail:xhli7489@sina.com
  • 作者简介:梁建新,高级工程师,主要研究方向为精密零件表面光整加工。E-mail:13935486349@139.com
  • 基金资助:
    国家自然科学基金项目(51975399,51875389,52575523);中央引导地方科技发展资金项目(YDZJSX2022A020,YDZJSX2022B004)

Influence of speed ratio on the centrifugal dry superfinishing performance of cylindrical rollers

LIANG Jianxin1, ZHAI Xunzheng2, LOU Tangyun1, WANG Xingfu3,4, WANG Jiaming3,4, LI Xiuhong3,4   

  1. 1 Jingwei Intelligent Textile Machinery Co.,Ltd.,Jinzhong 030600,China;
    2 AECC Aero Engine Corporation,Xi’an 710000,China;
    3 College of Mechanical Engineering,Taiyuan University of Technology,Taiyuan 030024,China;
    4 Shanxi Provincial National Defense Advanced Technology Innovation Center for Performance Manufacturing,Taiyuan 030024,China
  • Received:2025-11-25 Online:2026-09-18 Published:2026-10-22

摘要: 为研究离心干式超精滚抛工艺中转速比对GCr15圆柱滚子滚抛效果的影响,基于仿真分析,对不同转速比下的介质流团状态、干式介质作用于滚子表面的动力学行为及滚抛效果进行分析,确定了较优的转速比,并通过粒子图像测速(Particle Image Velocimetry,PIV)和滚抛试验进行验证。结果表明,随着转速比绝对值n/N的增大,介质流团不断膨胀,当转速比n/N=-3.5和1.5时,达到临界值,干式介质逐渐向壁面扩散,出现贴壁现象;当转速比n/N=-2.0时,滚抛效果最优;采用该参数对滚子滚抛加工后,外径面表面轮廓Sa、Sq值分别从0.144 μm、0.182 μm降至0.015 μm、0.021 μm,端面表面轮廓Sa、Sq值分别从0.207 μm、0.282 μm降至0.043 μm、0.068 μm,表面质量显著改善。

关键词: 离心干式超精滚抛, 转速比, 圆柱滚子, 颗粒介质动力学, 滚抛效果

Abstract: To investigate the influence of speed ratio on the centrifugal dry superfinishing performance of GCr15 cylindrical rollers,the flow state of the media cluster,the dynamic behavior of dry media on the roller surface,and the finishing performance under different speed ratios were analyzed based on numerical simulations. The optimal speed ratio was determined and further verified by Particle Image Velocimetry (PIV) and finishing experiments. The results showed that,with the increase of the absolute speed ratio n/N the media cluster expanded continuously. When the speed ratio n/N reached -3.5 and 1.5, critical points were reached,and the dry media gradually diffused toward the container wall,forming a wall-adhering phenomenon. The best finishing performance was achieved at a speed ratio of n/N=-2.0. After processing under this condition,the surface profile parameters Sa and Sq values of the outer diameter surface decreased from 0.144 μm and 0.182 μm to 0.015 μm and 0.021 μm,respectively,while those of the end surface decreased from 0.207 μm and 0.282 μm to 0.043 μm and 0.068 μm,respectively,indicating a substantial enhancement in surface quality.

Key words: centrifugal dry superfinishing, speed ratio, cylindrical roller, granular media dynamics, finishing performance

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn