现代制造工程 ›› 2026, Vol. 553 ›› Issue (10): 39-45.doi: 10.16731/j.cnki.1671-3133.2026.10.005

• 增材制造 • 上一篇    下一篇

TPMS薄壁内流道叶片结构设计及微3D打印制造研究

王英, 覃恩伟, 于霜   

  1. 苏州工业职业技术学院智能装备学院,苏州 215100
  • 收稿日期:2025-11-25 出版日期:2026-10-18 发布日期:2026-11-05
  • 作者简介:王英,博士研究生,讲师,主要研究方向为先进材料结构设计与力学性能。E-mail:wangying@siit.edu.cn。覃恩伟,博士研究生,高级工程师,主要研究方向为复杂结构设计与增材制造。于霜,博士研究生,副教授,主要研究方向为结构优化与控制。E-mail:275820361@qq.com

Research on structure design of thin-walled TPMS channels in turbine blades and manufacturing with micro 3D printing

Wang Ying, Qin Enwei, Yu Shuang   

  1. School of Intelligent Equipment, Suzhou Vocational Institute of Industrial Technology,Suzhou 215100,China
  • Received:2025-11-25 Online:2026-10-18 Published:2026-11-05

摘要: 微型涡轮发动机是无人装备的重要动力源。然而微型化使得涡轮叶片在极端高温环境下面临极大的热防护挑战。为突破传统冷却流道传热效率低、结构强度与轻量化的固有矛盾,提出了一种基于三周期极小曲面(Triply Periodic Minimal Surface,TPMS)的曲面冷却流道(薄壁内流道)设计方法,并结合微3D打印技术实现该复杂结构的高精度成型。研究选取G型TPMS结构,通过参数化优化设计,成功构建了兼具高比表面积和轻量化的薄壁内流道结构。优化后叶片传热面积显著增加到70 cm2,并实现了43.9 %的减重。通过系统对比不同工艺参数,利用微激光粉末床熔融(Micro-Laser Powder Bed Fusion,Micro-LPBF)技术,选用CoCr合金精细粉末,确定了微3D打印CoCr合金的最佳工艺参数,获得了相对致密度达99.67 %且表面粗糙度Ra低至1.4 mm的高质量成型件。有限元模拟结果表明,在1 273 K高温燃气环境下,相较于传统简化的实芯叶片模型,G型TPMS内流道结构能将模型整体工作温度降低700~800 K,展现出卓越的散热性能与主动热管理能力。该研究探索了微型涡轮发动机叶片冷却新方案和新制造工艺。初步验证结果显示,TPMS曲面冷却流道设计和微3D打印技术的结合有望在先进航空动力装置中开展工程应用。

关键词: 微3D打印, 三周期极小曲面, 冷却流道, 微无人飞行器, CoCr合金

Abstract: Micro gas turbine engines serve as a crucial power source for unmanned equipment. To address the thermal protection challenges of micro-turbine blades under extreme high-temperature environments and overcome the inherent trade-offs among heat transfer efficiency,structural integrity,and weight reduction in conventional cooling channels, a novel design approach for curved cooling channels based on Triply Periodic Minimal Surfaces (TPMS) was proposed,which were precisely fabricated via micro 3D printing. The Gyroid-type TPMS configuration was selected, parametrically designed,and optimized to create a thin-walled internal channel structure characterized by a high specific surface area and excellent mechanical properties. The optimized blade achieved a significant increase in internal heat transfer area (reaching 70 cm2) coupled with a remarkable 43.9 % reduction in weight. Through systematic parametric optimization,the optimal process parameters for Micro-Laser Powder Bed Fusion (Micro-LPBF) of CoCr alloy were identified, resulting in fabricated parts with a relative density of 99.67 % and a very low surface roughness Ra of 1.4 μm. Finite element simulations demonstrate that under a high-temperature gas condition of 1 273 K, the simplified blade model with the Gyroid-TPMS internal channels maintains an operating temperature 700~800 K lower than that of a conventional solid blade model,highlighting its exceptional heat dissipation and active thermal management capabilities. This study investigated a novel cooling strategy and manufacturing process for micro gas turbine blades. The preliminary validation results indicate that the integration of curved TPMS cooling channels design and micro 3D printing technology demonstrates promising potential for engineering applications in advanced aerospace propulsion systems.

Key words: micro 3D printing, Triply Periodic Minimal Surface(TPMS), cooling channel, micro Unmanned Aerial Vehicle (UAV), CoCr alloy

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn