Simulation of hydraulic excavator excavation resistance based on LS-DYNA

doi:10.16731/j.cnki.1671-3133.2018.08.014

Abstract

Abstract: Aiming at the difficulty of directly obtaining the load spectrum of excavation resistance through experimental testing,presents a method to obtain the load spectrum of excavation resistance through dynamic simulation.Firstly,the bucket-soil model is established in LS-PREPOST.Then select 3 representative excavation trajectories as the trajectory of the bucket model.Finally,the simulation of bucket digging soil is carried out,the load history of the bucket and three sets of cylinder thrust are obtained.According to the comparison between the calculated results and the measured data from a 36 t backhoe hydraulic excavator,the bucket-soil model is continuously improved,and the more accurate excavation resistance is obtained.The feasibility of the simulation method is verified.

Key words: hydraulic excavator, excavation resistance, simulation, LS-DYNA software, excavation trajectory

CLC Number:

TU 621

Chen Jin,Tong Le,Pang Xiaoping,Nie Dong,Zou Zhihong. Simulation of hydraulic excavator excavation resistance based on LS-DYNA[J]. Modern Manufacturing Engineering, 2018, 455(8): 75-80.

[1]	YING Jiangpeng, SUN Youping, WU Guangqing, CHEN Pengyu, JI Hongchun. Research on closed-loop control strategy of electromechanical brake clamping force [J]. Modern Manufacturing Engineering, 2025, 538(7): 48-56.
[2]	WANG Lei, ZHANG Lei, ZHANG Yue, LI Hongbing, SUN Ming, LU Guan. Design and research of four-fingered dexterous hand [J]. Modern Manufacturing Engineering, 2025, 535(4): 69-76.
[3]	LIANG Tong, BAI Yuhang, ZHANG Baoxu, LI Yanan, ZHAO Yanjun. Structural design and research of rehabilitation exoskeleton based on TRIZ for two-phase travel [J]. Modern Manufacturing Engineering, 2025, 535(4): 84-90.
[4]	LIU Liang, HE Yuming, QI Siyuan. Optimization study of flexible job-shop scheduling based on digital twin simulation [J]. Modern Manufacturing Engineering, 2025, 534(3): 41-51.
[5]	ZHOU Xianjun, LI Hai, PENG Yuxuan, YU Fuhao, FANG Hao. Study on the characteristics of special-shaped leaf spring of injection-production integrated automatic steering tool [J]. Modern Manufacturing Engineering, 2025, 532(1): 71-79.
[6]	ZHU Feng, YAO Jiannan. Design of magnetorheological damper vibration-damping suspension device for longitudinal vibration of mine hoisting system [J]. Modern Manufacturing Engineering, 2025, 532(1): 128-136.
[7]	CHENG Lanlan, XIONG Liangshan. The influence of J-C constitutive model parameters on the simulation results of 45 steel drilling [J]. Modern Manufacturing Engineering, 2024, 528(9): 20-24.
[8]	ZHANG Keming, CAO Yu, XI Shangbin, ZHENG Pei, ZHANG Zhenya, HUANG Jia, LIU Wencheng, YAO Jun. Fundamental mechanism of calibration coefficients considering the effect of the bonding process on the moiré interference drilling method [J]. Modern Manufacturing Engineering, 2024, 526(7): 1-8.
[9]	MA Liping, LI Shaopeng, ZHAO Yanping, CHENG Zixin, LIN Hongli. Research on modeling and simulation of electronic brake booster for new energy vehicles [J]. Modern Manufacturing Engineering, 2024, 525(6): 82-87.
[10]	LUO Zhonglong, ZHANG Xiuchao. Study on the influence of tooth profile modification on meshing interference phenomenon of planetary reducer [J]. Modern Manufacturing Engineering, 2024, 525(6): 88-94.
[11]	LIU Senlin, XING Fei, BIAN Hongyou, WANG Hai. Design simulation and experimental research on the structure of the waveform air inlet duct in selective laser melting [J]. Modern Manufacturing Engineering, 2024, 524(5): 138-144.
[12]	GAO Shanfeng, LEI Le, ZHAO Lun, YE Kai, LI Chengwang, ZHAO Shengsheng, SONG Zhendong, BAO Danyang. Study on forming mechanism and mechanical behavior of self-piercing riveting of aerospace aluminum and titanium alloys [J]. Modern Manufacturing Engineering, 2024, 523(4): 1-6.
[13]	LI Huan, YU Fei, LIU Ning, YU Zhenlong, ZHANG Mingyuan, LIU Yu, YANG Lei. Research on key technology of forward development of torsion beam based on numerical simulation [J]. Modern Manufacturing Engineering, 2024, 523(4): 94-101.
[14]	ZHANG Funeng, LIN Zhiwei, XUE Yong, LI Jiongqi, FU Jianzhong. Optimization of the milling cutter spiral groove grinding process based on grinding force [J]. Modern Manufacturing Engineering, 2024, 521(2): 61-67.
[15]	ZHANG Xing, DENG Jianxin. Research on cloud service system for cargo transportation damage analysis based on ANSYS [J]. Modern Manufacturing Engineering, 2024, 521(2): 102-111.

Simulation of hydraulic excavator excavation resistance based on LS-DYNA

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments