现代制造工程 ›› 2026, Vol. 552 ›› Issue (9): 104-110.doi: 10.16731/j.cnki.1671-3133.2026.09.012

• 制造技术/工艺装备 • 上一篇    下一篇

基于响应面法的硬质合金刀片断屑槽抛光工艺参数优化

师润平1, 彭斌1, 李素云1, 韩彦良1, 吴交2   

  1. 1 贺州学院,贺州 542899;
    2 深圳市鑫运祥精密刀具有限公司,深圳 518109
  • 收稿日期:2025-05-30 出版日期:2026-09-18 发布日期:2026-10-22
  • 作者简介:师润平,博士,研究员,曾长期在刀具制造企业从事技术和管理工作,主要研究方向为先进制造技术和现代高效刀具。彭斌,硕士,工程师,主要研究方向为非线性动力系统理论及数值方法。E-mail:shirunping@hzxy.edu.cn
  • 基金资助:
    国家自然科学基金项目(62366013)

Optimization of polishing process parameters for chip-breaking groove of cemented carbide insert based on response surface methodology

SHI Runping1, PENG Bin1, LI Suyun1, HAN Yanliang1, WU Jiao2   

  1. 1 Hezhou University,Hezhou 542899,China;
    2 Shenzhen Xinyunxiang Precision Cutting Tools Company,Shenzhen 518109,China
  • Received:2025-05-30 Online:2026-09-18 Published:2026-10-22

摘要: 降低硬质合金刀片的表面粗糙度值可以有效防止黏刀和形成积屑瘤,改进加工零件的表面质量和延长刀具寿命。带断屑槽的刀片前刀面无法进行精磨加工,针对断屑槽的特殊形貌,选择柔性毛刷抛光工艺降低刀片前刀面(断屑槽)的表面粗糙度值。采用响应曲面分析法和Box-Behnken原理设计四因素三水平实验,以进给量、加工时长、微粉粒度和刷轮转速为工艺参数,以刀片断屑槽区域的表面粗糙度为抛光效果评价指标,建立表面粗糙度的数值模型,获得优化后的抛光工艺参数,即进给量A=2 mm,加工时长B=19 min,微粉粒度C=1.04 μm,刷轮转速D=277 r/min。在该抛光工艺参数组合下,刀片断屑槽的表面粗糙度下降了54.5 %,达到了精磨刀片的表面粗糙度要求。

关键词: 硬质合金刀片, 毛刷抛光, 响应面法, 表面粗糙度, 工艺参数优化

Abstract: Reducing the surface roughness of cemented carbide inserts can effectively prevent tool adhesion and the formation of built-up edge,improve the surface quality of the machined part and extend the tool life. The rake face of inserts with chip-breaking groove cannot be finely ground. In view of the special morphology of the chip-breaking groove,a flexible brush polishing process was selected to reduce the surface roughness of the rake face (chip-breaking groove) of the inserts. The Box-Behnken design-response surface analysis method was used to design four factors three levels experiment, with feed rate,processing time,micro-powder particle size and brush wheel speed as process parameters,and the surface roughness of the chip-breaking groove area of the insert as the polishing effect evaluation index. A numerical model of surface roughness was established,and the optimized polishing process parameters were obtained include feed rate A=2 mm,processing time B=19 min,micro-powder particle size C=1.04 μm,and brush wheel speed D=277 r/min. Under this combination of polishing process parameters,the surface roughness of the chip-breaking groove of the insert decreased by 54.5 %,meeting the surface roughness requirements of finely ground inserts.

Key words: cemented carbide insert, brush polishing, response surface methodology, surface roughness, process parameter optimization

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn