现代制造工程 ›› 2026, Vol. 552 ›› Issue (9): 111-117.doi: 10.16731/j.cnki.1671-3133.2026.09.013

• 制造技术/工艺装备 • 上一篇    下一篇

齿廓修形对渐开线内啮合齿轮泵流量特性的影响

田徐阳, 刘赣华, 何文奎   

  1. 江西理工大学机电工程学院,赣州 341000
  • 收稿日期:2026-01-04 出版日期:2026-09-18 发布日期:2026-10-22
  • 通讯作者: 刘赣华,硕士,教授,主要研究方向为齿轮优化设计与制造。E-mail:liuganhua@jxust.edu.cn
  • 作者简介:田徐阳,硕士研究生,主要研究方向为内啮合齿轮泵设计及齿轮修形理论。
  • 基金资助:
    江西省教育厅科学研究项目(GJJ180454)

The influence of tooth profile modification on the flow characteristics of an involute internal gear pump

TIAN Xuyang, LIU Ganhua, HE Wenkui   

  1. School of Mechanical and Electrical Engineering,Jiangxi University of Science and Technology,Ganzhou 341000,China
  • Received:2026-01-04 Online:2026-09-18 Published:2026-10-22

摘要: 齿廓修形是提升内啮合齿轮泵性能的一种有效设计手段。采用理论推导与数值计算相结合的研究方法,重点分析了端面齿廓倾斜修形、修根修缘两种修形方式对渐开线内啮合齿轮泵流量特性的影响机制。首先基于修形原理建立修形齿廓的数值模型,然后根据啮合原理与扫过面积法建立齿轮泵瞬时流量模型,并以流量脉动系数作为内啮合齿轮泵的性能评价指标。结果表明,端面齿廓倾斜修形会降低齿轮泵瞬时流量,同时增大流量脉动系数;修根修缘则会改变齿廓的啮合区域并影响流量特性,随着修形量的增大,齿轮泵瞬时流量逐渐提高;修根修缘能够有效减小齿轮泵流量脉动系数,使其从未修形时的2.409 %降低至1.328 %。

关键词: 修形, 渐开线内啮合齿轮泵, 瞬时流量, 流量脉动

Abstract: Tooth profile modification serves as an effective design approach for enhancing the performance of internal gear pumps. A combined methodology of theoretical derivation and numerical computation is employed to investigate the influence mechanisms of two profile modification methods—face profile tilting modification,and root and tip relief—on the flow characteristics of involute internal gear pumps. A numerical model of the modified tooth profiles is first established based on modification principles,followed by the development of an instantaneous flow rate model for the gear pump using meshing theory and the swept area method. The flow pulsation coefficient is adopted as the performance evaluation indicator for the internal gear pump. Results demonstrate that face profile tilting modification reduces the instantaneous flow rate while increasing the flow pulsation coefficient. In contrast,root and tip relief alters the meshing zone of the tooth profile and influences flow characteristics. As the amount of modification increases,the instantaneous flow rate gradually improves. Moreover,root and tip relief effectively reduces the flow pulsation coefficient,lowering it from 2.409 % in the unmodified condition to 1.328 %.

Key words: modification, involute internal gear pump, instantaneous flow rate, flow pulsation

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn