Study on kinematics simulation of high-simulation chewing platform based on UG and ADAMS

doi:10.16731/j.cnki.1671-3133.2017.02.007

Modern Manufacturing Engineering ›› 2017, Vol. 437 ›› Issue (2): 35-39.doi: 10.16731/j.cnki.1671-3133.2017.02.007

Previous Articles Next Articles

Study on kinematics simulation of high-simulation chewing platform based on UG and ADAMS

Li Xiang¹, Wang Jiasen¹, Han Jinghu¹, Zhang Tiehu¹, Yu Jinghu^1,2

1 School of Mechanical Engineering,Jiangnan University,Wuxi 214122,Jiangsu,China
2 Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology,Wuxi 214122,Jiangsu,China

Received:2015-06-17 Online:2017-02-28 Published:2018-01-08

Abstract

Abstract: The kinematics simulation of the high-simulation chewing platform was analyzed based on the Unigraphics NX 3D modeling.Under the condition of ADAMS,a virtual prototype model of this simulation chewing platform was set up.The graphs of the position,velocity and acceleration of specific human chewing simulation movement by the mobile platform were generated.The results show that the chewing platform can simulate the performance of human chewing thoroughly,and the simulation results can provide a good foundation for the research on high-quality control method.

Key words: food, high-simulation chewing platform, Unigraphics NX, kinematics, ADAMS software

CLC Number:

TN98

Li Xiang, Wang Jiasen, Han Jinghu, Zhang Tiehu, Yu Jinghu. Study on kinematics simulation of high-simulation chewing platform based on UG and ADAMS[J]. Modern Manufacturing Engineering, 2017, 437(2): 35-39.

[1]	ZHAO Jiawei, LI Weidong, ZHOU Yong, HU Jiquan. Rotation modeling and geometric inverse optimization of milling robot [J]. Modern Manufacturing Engineering, 2024, 523(4): 66-72.
[2]	ZHANG Fengxin, SUN Zhenxing. End traction upper limb exoskeleton structure design and kinematics analysis [J]. Modern Manufacturing Engineering, 2024, 521(2): 120-127.
[3]	WANG Binghao, SUN Longfei. Structural design and grasping morphology study of differential drive manipulator [J]. Modern Manufacturing Engineering, 2024, 530(11): 73-79.
[4]	Ge Zhedong, Zhang Lianbin, Gu Yuanhui, Su Chen, Zhou Yucheng. Design and kinematics research of a wood inspection robot [J]. Modern Manufacturing Engineering, 2019, 460(1): 59-63.
[5]	Wang Jun, Li Shuting, Hao Fang, Chen Zhilong, He Hongxiu, Yang Zhiyong. Study on design and molding quality of selective laser sintering [J]. Modern Manufacturing Engineering, 2018, 454(7): 12-16.
[6]	Ding Chengjun, Zhang Peng, Yan Bin. Construction and experimental study of motion control model for a novel extrusion system [J]. Modern Manufacturing Engineering, 2018, 459(12): 31-38.
[7]	Sun Jianghong, Niu Xiaohui, Liu Xu. Kinematics analysis of a kind of automatic folding stage [J]. Modern Manufacturing Engineering, 2017, 443(8): 1-6.
[8]	Gao Han, Zhang Minglu, Zhang Xiaojun, Gao Baijun, Huang Xiaochen. Study on an approach to the solution of inverse kinematics for redundant manipulators [J]. Modern Manufacturing Engineering, 2017, 443(8): 29-33.
[9]	Ye Renping, Zeng Dehuai. Research on coordinated simulation of robot arm motion control based on Adams and Matlab [J]. Modern Manufacturing Engineering, 2017, 441(6): 56-61.
[10]	Li Jiangbo, Wu Anru, Chen Jun. Dynamic simulation study of a die forging press based on ADAMS [J]. Modern Manufacturing Engineering, 2017, 447(12): 155-159.
[11]	Liu Chun, Wei Yafei, Zhang Hongrui. Design scheme and simulation verification of holding device for die-changing under high temperature [J]. Modern Manufacturing Engineering, 2017, 445(10): 19-23.

Study on kinematics simulation of high-simulation chewing platform based on UG and ADAMS

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 11

Recommended Articles

Metrics

Comments