现代制造工程 ›› 2026, Vol. 553 ›› Issue (10): 98-108.doi: 10.16731/j.cnki.1671-3133.2026.10.012

• CAD/CAE/CAPP/CAM • 上一篇    下一篇

基于本体的典型特征加工方案管理与复用方法*

李文琪1,2, 高琦1,2, 王萍3, 张善辉1,2, 赵远1,2   

  1. 1 山东大学机械工程学院,济南 250061;
    2 山东大学高效洁净机械制造教育部重点实验室,济南 250061;
    3 山东山大华天软件有限公司,济南 250101
  • 收稿日期:2025-11-23 出版日期:2026-10-18 发布日期:2026-11-05
  • 通讯作者: 高琦,博士,教授,主要研究方向为产品生命周期管理、知识工程、智能设计和工业机器人。E-mail:gaoqi@sdu.edu.cn
  • 作者简介:李文琪,硕士研究生,主要研究方向为工艺设计、数控编程。
  • 基金资助:
    *山东省重点研发计划项目(2023CXPT003);四川省重大科技专项项目(2022ZDZX0010)

Method for managing and reusing machining schemes of typical features based on ontology

Li Wenqi1,2, Gao Qi1,2, Wang Ping3, Zhang Shanhui1,2, Zhao Yuan1,2   

  1. 1 School of Mechanical Engineering,Shandong University,Jinan 250061,China;
    2 Key Laboratory of High-Efficiency and Clean Mechanical Manufacture,Ministry of Education,Shandong University,Jinan 250061,China;
    3 Shandong Hoteam Software Co.,Ltd.,Jinan 250101,China
  • Received:2025-11-23 Online:2026-10-18 Published:2026-11-05

摘要: 在产品工艺规划阶段,大量具有复用价值的工艺知识未被有效管理和利用,现有基于传统匹配方式的工艺方案复用缺乏语义理解且依赖人工经验,需要多次调整,导致工艺规划效率和标准化程度较低。针对以上问题,提出了一种基于本体的典型特征加工方案管理与复用方法。首先,分析零件的典型特征类型以及工艺知识,构建了典型特征工艺知识本体模型;然后,提出了一种综合概念语义和属性值的两阶段相似度计算与案例复用机制;最后,以某企业航空典型零件地梁板的孔、平面特征为例,进行案例的搜索与匹配验证,结果表明,基于本体的典型特征加工方案管理与复用方法可有效管理和复用特征工艺知识,证实了该方法的有效性。

关键词: 典型特征, 加工方案, 本体, 语义相似度, 案例复用

Abstract: In the stage of product process planning,a large amount of reusable process knowledge has not been effectively managed or utilized. Existing process plan reuse methods based on traditional matching approaches lack semantic understanding and rely heavily on human expertise,requiring multiple manual adjustments and resulting in low efficiency and poor standardization of process planning. To address these issues,this study proposes an ontology-based method for managing and reusing typical feature machining schemes. First,the typical feature types of parts and corresponding process knowledge are analyzed to construct a feature-oriented process knowledge ontology model. Then,a two-stage similarity calculation and case reuse mechanism that integrates conceptual semantics and attribute values is developed. Finally,a case study is conducted on the hole and plane features of an aircraft beam-plate component from an enterprise to verify the proposed method. The results demonstrate that the method for managing and reusing machining schemes of typical features based on ontology can effectively manage and reuse feature process knowledge,confirming its feasibility and effectiveness.

Key words: typical feature, feature machining scheme, ontology, semantic similarity, case reuse

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn