现代制造工程 ›› 2026, Vol. 553 ›› Issue (10): 122-127.doi: 10.16731/j.cnki.1671-3133.2026.10.015

• 制造技术/工艺装备 • 上一篇    下一篇

电液作动器的孔轴类零件自动对中工艺技术的仿真及装配验证*

王朝阳1,2, 唐庸2,3, 徐子乔2,3, 李飞2,3, 潘乐2, 万强2, 易建军1   

  1. 1 华东理工大学机械与动力工程学院,上海 200237;
    2 上海航天控制技术研究所,上海 201109;
    3 上海市伺服系统工程技术研究中心,上海 201109
  • 收稿日期:2025-03-31 出版日期:2026-10-18 发布日期:2026-11-05
  • 通讯作者: 易建军,博士,教授,主要研究方向为工业机器人、多信息感知与模式识别以及基于视觉的伺服控制。E-mail:jjyi@ecust.edu.cn
  • 作者简介:王朝阳,博士,工程师,主要研究方向为现役运载火箭配套伺服机构精密装配工艺技术。E-mail:y16240115@mail.ecust.edu.cn
  • 基金资助:
    *2021年上海航天技术研究院工艺技术课题项目

Simulation and assembly verification of automatic centering process technology for hole axis type part of electro-hydraulic actuator

Wang Chaoyang1,2, Tang Yong2,3, Xu Ziqiao2,3, Li Fei2,3, Pan Le2, Wan Qiang2, Yi Jianjun1   

  1. 1 School of Mechanical and Power Engineering, East China University of Science and Technology,Shanghai 200237,China;
    2 Shanghai Aerospace Control Technology Institute,Shanghai 201109,China;
    3 Shanghai Engineering Research Center of Servo Systems,Shanghai 201109,China
  • Received:2025-03-31 Online:2026-10-18 Published:2026-11-05

摘要: 针对某直线型电液伺服机构作动器组件的孔轴类零件在装配过程中产生偏心挤压的问题,提出了电液作动器自动对中装配工艺技术,创新性地运用了孔轴间偏心率造成密封圈轴向受压缩后回弹的原理,实现了在线调节对中位置。基于偏心力控制值设计相应的可浮动水平滑台,开发了适用于直线型电液伺服机构作动器组件的自动对中装配设备。采用结构仿真及理论计算的研究方法,确定了在线调节对中所需的最小偏心作用力,并取1.5的裕量系数确定可浮动水平滑台的最大滑移阻尼控制值(偏心力控制值)为29.38 N。使用该设备进行了电液作动器自动对中装配试验,结果表明,电液作动器自动对中装配工艺技术解决了孔轴间偏移问题,较传统手工装配方法,一次装机合格率由不到80 %提升至100 %;装配面无异常划痕、密封件切损等异常,简约且低成本地解决了某直线型电液伺服机构作动器组件的孔轴类零件在装配过程中产生的偏心挤压问题,最终达到了提升电液作动器装配质量稳定性的效果。

关键词: 电液作动器, 自动对中装配, 工艺技术, 仿真, 验证

Abstract: Aiming at the problem of eccentric compression of the hole axis type part of a linear electro-hydraulic servo mechanism actuator component during assembly,and innovatively utilizing the principle of axial compression rebound of the sealing ring caused by the eccentricity between the hole and axis,an automatic centering assembly process technology for the electro-hydraulic actuator was proposed to achieve online adjustment of the centering position. A corresponding floating horizontal sliding table was designed based on the eccentric force control value,and an automatic centering assembly device suitable for linear electro-hydraulic servo mechanism actuator components was developed. The research methods of structural simulation and theoretical calculation were adopted to determine the minimum eccentric force required for online adjustment,and 1.5 times the margin was taken to determine the maximum sliding damping control value of the corresponding floating horizontal sliding table as 29.38 N. The automatic centering assembly test of the electro-hydraulic actuator was conducted using this device. The results show that the automatic centering assembly process technology of the electro-hydraulic actuator solves the problem of offset between the hole and axis,and compared with traditional manual assembly methods,the once installation qualification rate has increased from less than 80 % to 100 %. There are no abnormal scratches or seal cuts on the assembly surface,and the problem of eccentric compression of the hole axis type parts of a linear electro-hydraulic servo mechanism actuator component during assembly is solved simply and at low cost,ultimately achieving the effect of improving the stability of electro-hydraulic actuator assembly quality.

Key words: electro-hydraulic actuator, automatic centering assembly, process technology, simulation, verification

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn