现代制造工程 ›› 2026, Vol. 552 ›› Issue (9): 92-103.doi: 10.16731/j.cnki.1671-3133.2026.09.011

• CAD/CAE/CAPP/CAM • 上一篇    下一篇

基于联合本构模型的高强钢CTB电池箱体横纵梁辊弯成形回弹预测

覃频频1, 吴林周1, 黄俊明1, 徐敏敏1, 陆俊成2, 唐玉贵2   

  1. 1 广西大学机械工程学院,南宁 530004;
    2 广西巨石新能源科技有限公司,南宁 530009
  • 收稿日期:2026-01-19 出版日期:2026-09-18 发布日期:2026-10-22
  • 作者简介:覃频频,博士,副教授,硕士研究生导师,主要研究方向为车辆动力学与系统安全。E-mail:qpinpin@gxu.edu.cn
  • 基金资助:
    广西重点研发计划项目(桂科AB25069452);广西自然科学基金项目(2024GXNSFBA010142)

Prediction of roll forming springback for high-strength steel CTB battery box crossbeams and longitudinal beams based on a combined constitutive model

QIN Pinpin1, WU Linzhou1, HUANG Junming1, XU Minmin1, LU Juncheng2, TANG Yugui2   

  1. 1 School of Mechanical Engineering,Guangxi University,Nanning 530004,China;
    2 Guangxi Huge Stone New Energy Technology Co.,Ltd.,Nanning 530009,China
  • Received:2026-01-19 Online:2026-09-18 Published:2026-10-22

摘要: 为解决高强钢在电池车身一体化(Cell to Body,CTB)电池箱体横纵梁辊弯成形中回弹预测精度不足的问题,构建“屈服准则-硬化模型-弹性模量衰减模型”递进式联合本构模型,开展回弹预测规律探究。首先通过准静态条件下3个方向单轴拉伸试验、循环加载-卸载试验,分别完成Hill48各向异性屈服准则、Mises各向同性屈服准则、Swift非饱和各向同性硬化模型、Hockett-Sherby(H-S)饱和硬化模型及弹性模量衰减模型的参数标定;其次在有限元分析软件ABAQUS中建立20道次辊弯有限元模型;最后通过对比分析不同联合本构模型的回弹预测精度,明确各本构要素的影响规律。有限元仿真结果表明,Hill48各向异性屈服准则较Mises各向同性屈服准则可降低回弹预测精度偏差20.6 %~38.3 %,表明高强钢在Hill48各向异性屈服准则下改善效果更显著;Hockett-Sherby饱和硬化模型较Swift非饱和各向同性硬化模型可降低回弹预测精度偏差17.2 %~35.7 %;在“Hill48+H-S”最优基础联合本构模型中引入弹性模量衰减模型后,平均回弹角偏差从1.19°降至1.08°。相比“Mises+Swift”联合本构模型的2.33°回弹角初始偏差,递进式联合本构模型回弹预测精度提升了53.6 %。结果验证了递进式联合本构模型的有效性,可为高强钢CTB技术横纵梁的精密辊弯成形工艺提供理论依据。

关键词: DP780高强钢, 联合本构模型, 辊弯成形, 回弹预测, 弹性模量衰减

Abstract: To address the insufficient prediction accuracy of springback in the roll-forming process of longitudinal and transverse beams for CTB integrated structure battery boxes made of high-strength steel, it established a progressive joint constitutive research framework comprising ″yield criterion-hardening model-elastic modulus decay model″ to investigate the springback prediction mechanism. First, parameters for the Hill48/Mises yield criterion, Swift/Hockett-Sherby (H-S) hardening model, and elastic modulus decay model were calibrated through quasi-static triaxial uniaxial tensile tests and cyclic loading-unloading experiments. Second, a finite element model of a 20-pass roll bend was established in finite element analysis software. Finally, by comparing the springback prediction accuracy of different combined constitutive models, the influence patterns of each constitutive element were clarified. Finite element simulation results indicate that the Hockett-Sherby saturated hardening model reduces deviation by 17.2 %~35.7 % compared to the Swift model, with more pronounced improvement under the Hill48 yield criterion. Introducing elastic modulus decay into the ″Hill48+H-S″ optimal base coupled constitutive model reduces the average springback angle deviation from 1.19° to 1.08°. Compared to the 2.33° initial deviation of the ″Mises+Swift″ model, the optimal model achieved a 53.6 % improvement in prediction accuracy. This study validates the effectiveness of three-dimensional coupled constitutive models, providing a theoretical basis for precision roll bending processes of high-strength steel CTB longitudinal beams.

Key words: DP780 high-strength steel, combined constitutive model, roll forming, springback prediction, elastic modulus decay

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn