现代制造工程 ›› 2026, Vol. 553 ›› Issue (10): 31-38.doi: 10.16731/j.cnki.1671-3133.2026.10.004

• 增材制造 • 上一篇    下一篇

面向增材制造的TC4钛合金薄壁轴流机匣拓扑-尺寸协同优化研究

汪文君1,2, 孟卫华1,2, 李敏1,2, 李坚1,2, 金海良1,2, 李维1,2   

  1. 1 中国航发湖南动力机械研究所,株洲 412002;
    2 中小型航空发动机联合研究中心,株洲 412002
  • 收稿日期:2025-10-22 出版日期:2026-10-18 发布日期:2026-11-05
  • 通讯作者: 汪文君,硕士,高级工程师,主要研究方向为复合材料构件强度设计、结构拓扑优化设计。E-mail:mifeng_2005@163.com

Topology-size collaborative optimization of thin-walled axial flow casing fabricated from TC4 titanium alloy via additive manufacturing

Wang Wenjun1,2, Meng Weihua1,2, Li Min1,2, Li Jian1,2, Jin Hailiang1,2, Li Wei1,2   

  1. 1 AECC Hunan Aviation Powerplant Research Institute,Zhuzhou 412002,China;
    2 United Research Center of Mid-Small Aero-Engine,Zhuzhou 412002,China
  • Received:2025-10-22 Online:2026-10-18 Published:2026-11-05

摘要: 为突破传统航空发动机轴流机匣设计瓶颈,针对TC4钛合金薄壁轴流机匣开展静态工况下拓扑与尺寸协同优化及验证研究。以质量最小为目标,耦合力学性能与增材制造工艺约束,采用变密度法完成拓扑优化以获取最优构型,再以筋梁壁厚为设计变量,结合ANSYS仿真开展尺寸精细化优化。通过选区激光熔化(Selective Laser Melting,SLM)工艺试制及静力试验验证,结果表明,优化后机匣可满足强度与刚度要求,质量减小了8.7 %。构建了设计-制造-验证一体化体系,实现了设计驱动制造升级,可为轴流机匣增材制造设计提供可靠技术参考,对推动航空工业自主可控具有重要战略意义。

关键词: 薄壁轴流机匣, 拓扑优化, 金属增材制造, 尺寸优化, TC4钛合金

Abstract: To address the design bottlenecks of traditional aero-engine axial flow casings,collaborative topology and dimensional optimization together with verification were carried out for TC4 titanium alloy thin-walled axial flow casings under static operating conditions. With mass minimization as the objective,mechanical performance constraints and additive manufacturing process constraints were coupled. The variable density method was adopted to perform topology optimization and obtain the optimal configuration. Subsequently,the wall thickness of ribs and beams was taken as design variable, and refined dimensional optimization was conducted in combination with ANSYS simulation. Prototype fabrication was performed using Selective Laser Melting (SLM) process,followed by static test verification. The results demonstrated that the optimized casing can satisfy the high strength and stiffness requirements,with a mass reduction of 8.7 %. An integrated design-manufacturing-verification system was established,enabling manufacturing upgrading driven by design. The proposed method can provide a reliable technical reference for the additive manufacturing design of axial flow casings and is of strategic significance for promoting independent and controllable development of the aviation industry.

Key words: thin-walled axial flow casing, topology optimization, metal additive manufacturing, size optimization, TC4 titanium alloy

中图分类号: 

版权所有 © 《现代制造工程》编辑部 
地址:北京市东城区东四块玉南街28号 邮编:100061 电话:010-67126028 电子信箱:2645173083@qq.com
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn